Liang, S. Y. and Tsao, T. C., Editors, Monitoring and Control for Manufacturing Processes, PED-Vol. 44, New York: American Society of Mechanical Engineers (1990).
Liang, S. Y. and Wu, C. L., Editors, Sensors and Signal Processing for Manufacturing, PED-Vol. 55, New York: American Society of Mechanical Engineers (1992).
Liang, S. Y., Editor, Proceedings of Joint US-Taiwan Symposium on Advanced Manufacturing Processes, National Science Foundation (1993).
Tsao, T.-C., Hu, J.-S., N. Olgac, Liang, S. Y., and Wiens, G. J., Editors, Mechatronics, DSC-Vol. 50, PED-Vol. 63, New York: American Society of Mechanical Engineers (1993).
Mechanical Engineering Handbook, Chapter 1: Material Processing, Fabrication, and Assembly, Section B: Fabrication: Machining (1997, 2005), CRC Press, Frank Kreith, Editor.
Manufacturing Science and Engineering, Contributing Editor, MED-Vol. 10, New York, American Society of Mechanical Engineers (1999).
Liang, S. Y. and Tatsuo, A., Editors, Proceedings of Japan-USA Symposium on Flexible Automation, American Society of Mechanical Engineers (2000).
Liang, S. Y., Editor, Transactions of North American Manufacturing Engineering Research Institution of the Society of Manufacturing Engineers (2003).
Liang, S. Y., Editor, Transactions of North American Manufacturing Engineering Research Institution of the Society of Manufacturing Engineers (2004).
Wang, L. and Gao R. X., Condition Monitoring and Control for Intelligent Manufacturing, Springer, “Advanced Diagnostics and Prognostics Techniques for Rolling Element Bearings,” Kurfess, T. R., Billington, S., and Liang, S. Y., pp. 137-167. (2006).
Refereed Publications (Selected)
Liang, S. Y., "An Innovated Manufacturing Process for Fiberglass Reinforced Plastics," Annual of Chinese Institute of Engineers, NCKU, Vol. 4, pp. 35-40, 1979.
Liang, S. Y. and Dornfeld, D. A., "Punch Stretching Process Monitoring Using Emission Signal Analysis, Part I: Basic Characteristics," Journal of Acoustic Emission, 6, 1, pp. 29-36, 1987.
Liang, S. Y., Dornfeld, D. A., and Nickerson, J. A., "Punch Stretching Process Monitoring Using Acoustic Emission Signal Analysis, Part II: Application of Frequency Domain Deconvolution," Journal of Acoustic Emission, 6, 1, pp. 37-43, 1987.
Rangwala, S., Liang, S. Y., and Dornfeld, D. A., "Pattern Recognition of Acoustic Emission Signals During Sheet Metal Forming," Mechanical Systems and Signal Processing, 1(4), Academic Press, London, pp. 321-332, 1987.
Liang, S. Y. and Dornfeld, D. A., "Detection of Cutting Tool Wear Using Time Series Modeling of Acoustic Emission Signals," Proceedings of the Symposium on Sensors for Manufacturing, ASME Winter Annual Meeting, Boston, PED-Vol. 26, pp. 27-38, 1987.
Liang, S. Y., "Adaptive Control of Flexible Machining Using Acoustic Emission," Proc. 6th Annual Conference on University Programs in Computer Aided Engineering, Design, June 1988, pp. 170-176.
Liang, S. Y. and Dornfeld, D. A., "An Analytical Relationship between Acoustic Emission and Stretch Forming Process Parameters," Proceedings of the 16th North American Manufacturing Research Conference pp. 22-26, Urbana, May 1988.
Liu, M. and Liang, S. Y., "Model Reference Adaptive Control for Non-minimum Phase Milling," Transactions of the North American Manufacturing Research Institution, Society of Manufacturing Engineers, pp. 266-273, 1989.
Liang, S. Y., and Dornfeld, D. A., " Detection of Cutting Tool Wear Using Time Series Modeling of Acoustic Emission Signals," Transactions of the ASME, Journal of Engineering for Industry, Vol. 111, No. 3, pp. 199-205, 1989.
Liang, S. Y., Horng, M. C., and Liu, M., "Runout Compensation in Peripheral Milling Using Repetitive Control," Proceedings of the Symposium on Advances in Manufacturing Systems Engineering, ASME Winter Annual Meeting, PED-Vol. 37, pp. 77-87, San Francisco, December 1989.
Liang, S. Y. and Dornfeld, D. A., "Characterization of Sheet Metal Forming Using Acoustic Emission," Transactions of the ASME, Journal of Engineering Materials and Technology, Vol. 112, pp. 44-51, 1990.
Liu, M. and Liang, S. Y., "Monitoring of Peripheral Milling Using Acoustic Emission," Transactions of the North American Manufacturing Research Institution, Society of Manufacturing Engineers, pp. 120-127, 1990.
Liang, S. Y. and Chiou, Y. S., "Modeling of Acoustic Emission Sensing Dynamics for Drilling Process Control," Proceedings of the Japan-USA Symposium on Flexible Automation, pp. 695-702, Kyoto, Japan, June 1990.
Liu, M. and Liang, S. Y., "Dynamic Modeling of Acoustic Emission for Control of Peripheral Milling Process," Proceedings of the Symposium on Modeling of Machine Tools: Accuracy, Dynamics and Control, pp. 133-148, ASME Winter Annual Meeting, Dallas, PED-Vol. 45, November 1990.
Liu, M. and Liang, S. Y., "Analytical Modeling of Acoustic Emission for Monitoring of Peripheral Milling Processes," International Journal of Machine Tool and Manufacture, Vol. 31, No. 4, pp. 589-606, 1991.
Wang, J.-J., Liang, S. Y., and Book, W. J., "Analysis of Cutting Forces in End Milling via Angular Convolution," Proceedings of the Symposium on Sensors, Controls, and Quality Issues in Manufacturing, pp. 135-150, ASME Winter Annual Meeting, Atlanta, PED-Vol. 55, December 1991.
Chiou, Y. S., Tavakoli, M. S., and Liang, S. Y., "Bearing Fault Detection Based on Multiple Signal Features Using Neural Network Analysis," Proceedings of the 10th International Modal Analysis Conference, Society for Experimental Mechanics, pp. 60-64, San Diego, February 1992.
Liang, S. Y. and Perry, S., "Milling Cutter Runout Compensation by Control of Radial Depth of Cut" Proceedings of the USA-Japan Symposium on Flexible Automation, pp. 861-864, San Francisco, July 1992.
Wang, J. J., Liang, S. Y., and Book, W. J., "A Closed Form Frequency Domain Model for Tangential Cutting Force in Peripheral Milling," Proceedings of the Symposium on Physics of Machining Processes, PED-Vol. 63, pp. 53-66, ASME Winter Annual Meeting, Anaheim, November 1992.
Wang, J.-J. and Liang, S. Y., "Analysis of Force Pulsations in Relation to Machining Parameters in Milling," Journal of Mechatronic Industry, Vol. 120, pp. 212-219, 1993.
Liang, S. Y., Wang, J.-J., and Herman, P. A., "Surface Finish Enhancement in Milling via Inverse Runout Trajectory Following of Workpiece," Transactions of the North American Manufacturing Research Institution, Society of Manufacturing Engineers, pp. 103-109, May 1993.
Chung, E. S., Chiou, Y. S., and Liang, Y. S., “Time-Series Based Neural Network for the Detection of Tool Wear and Chatter in Machining,” Proceedings of the 26th International Symposium on Automotive Technology and Automation, pp. 257-264, Aachen, Germany, September 1993.
Liang, S. Y. and Urquhart-Foster, J. A., "Monitoring of In-situ Filament Winding Process Using Dynamic Dielectric Sensor," Proceedings of the Symposium on Mechatronics, pp. 261-269, ASME Winter Annual Meeting, New Orleans, November 1993.
Chiou, Y. S., Chung, E.-S., and Liang, S. Y., "Multiple Time Series Model for Neural Network Analysis of Tool Wear and Chatter in Turning," Proceedings of the Symposium on Intelligent Design and Manufacturing, pp. 351-358, ASME Winter Annual Meeting, New Orleans, November 1993.
Wang, J.-J., Liang, S. Y. and Book, W. J. "Convolution Analysis of Milling Force Pulsation," Transactions of the ASME, Journal of Engineering for Industry, Vol. 116, pp. 17-25. February 1994.
Liang, S. Y. and Perry, S. A., "In-Process Compensation for Milling Cutter Runout via Chip Load Manipulation," Transactions of the ASME, Journal of Engineering for Industry, Vol. 116, No. 2, pp. 153-160, 1994.
Chung, E.-S., Chiou, Y. S., and Liang, S. Y., “Tool Wear and Chatter Detection in Turning via Time-Series Modeling and Frequency Band Averaging,” (in English) Transactions of the Korean Society of Precision Engineering, Vol. 11, No. 2, pp. 75-84, April 1994.
Liang, S. Y. and Zheng, L., “Chip Load Servo for Runout Rejection in End Milling,” Proceedings of the USA-Japan Symposium on Flexible Automation, pp. 1471-1474, Kobe, Japan, July 1994.
Liang, S. Y. and Wang, J.-J., "Milling Force Convolution Modeling for Identification of Cutter Axis Offset," International Journal of Machine Tools and Manufacture, Vol. 34, No. 8, pp. 1171-1190, November 1994.
Liang, S. Y. and Wang, J. J. Junz, “Identification of Cutter Axis Offset in Milling via Force Analysis,” Proceedings of the Symposium on Physics of Machining Processes, pp. 175-186, ASME Winter Annual Meeting, Chicago, November 1994.
Stevens, A. J. and Liang, S. Y., “Runout Rejection in End Milling through Two-Dimensional Repetitive Force Control,” International Journal of Mechatronics, Issue 1, Vol. 5, pp. 1-13, March 1995.
Zheng, L. and Liang, S. Y., “Analysis of End Milling Forces with Cutter Axial Tilt,” Transactions of the North American Manufacturing Research Institution, Society of Manufacturing Engineers, pp. 137-142, May 1995.
Chiou, Y. S., Chung, E. S., and Liang, S. Y., “Analysis of Effect of Tool Wear Effect on Chatter Stability in Turning,” International Journal of Mechanical Sciences, Vol. 37, No. 4, pp. 391-404, April 1995.
Zheng, L., Chiou, Y. S., and Liang, S. Y., “Three Dimensional Cutting Force Analysis in End Milling,” International Journal of Mechanical Sciences, Vol. 38, No. 3, pp. 259-269, 1995.
Liang, S. Y., “Control of Cutter Runout in Milling via Chip Load Servo,” Proceedings of the third International Conference on Robotics and Manufacturing, pp. 122-125, IASTED, June 1995.
Lazoglu, I. and Liang, S. Y., “Dynamic Cutting Forces in Ball-End Milling,” Proceedings of ASME International Conference on Recent Advances in Mechatronics, pp. 940-945, Istanbul, Turkey, August 14-16, 1995.
Shorr, M. J. and Liang, S. Y., “Dynamic Stability Analysis for Multi-Flute End Milling,” Proceedings of 1995 Design Engineering Technical Conferences, DE-Vol. 84-3, Part C, pp. 307-315, ASME September 1995.
Lazoglu, I. and Liang, S. Y., “Analysis of Force System in Ball-End Milling,” Proceedings of Symposium on Manufacturing Science and Engineering, MED-Vol. 2-1/MH-Vol. 3-1, pp. 179-187, ASME International Mechanical Engineering Congress and Exposition, November 1995.
Wang, J.-J. and Liang, S. Y., "Chip Load Kinematics in Milling with Radial Cutter Runout," Transactions of the ASME, Journal of Engineering for Industry, Vol. 118, pp. 111-116, February 1996.
Shorr, M. J. and Liang, S. Y., “Chatter Stability Analysis for End-Milling Via Convolution Modeling,” International Journal of Advanced Manufacturing Technology, Vol. 11/4, pp. 311-318, 1996.
Wang, J.-J. and Liang, S. Y., “Chip Load Kinematics in Milling with Radial Cutter Runout,” Proceedings of Wu Symposium on Manufacturing Science, ASME, pp. 43-49, Ann Arbor, May 1996.
Lazoglu, I. and Liang, S. Y., “Milling Force Analysis for Complex Workpiece”, Proceedings of CSME Forum, pp. 373-381, Hamilton, Canada, May 1996.
Hekman, K. A. and Liang, S. Y., “On-line Identification of End Milling Cutter Runout,” Proceedings of the 1996 IPC Conference and Exposition, pp. 49-54, SAE, Detroit, May 1996.
Liang, S. Y., “Precision Milling with Chip Load Servo Compensation,” Proceedings of Dedicated Conference on Mechatronics-Advanced Development Methods and Systems for Automotive Products, ISATA, pp. 309-316, Florence, Italy, June 1996.
Hekman, K. A. and Liang, S. Y., “Real-time Identification of Cutter Axis Offset in End Milling,” Proceedings of Japan-USA Symposium on Flexible Automation, pp. 1215-1219, Boston, July 1996.
Chiou, Y. S. and Liang, S. Y., “A Study of Chatter Frequency of a Cutting Tool with Tool Wear in Turning,” Proceedings of Symposium on the Physics of Machining Processes, III, pp. 209-223, ASME International Mechanical Engineering Congress and Exposition, Symposium on Physics of Machining Processes, Atlanta, November 1996.
Lazoglu, I. and Liang, S. Y., “Feedrate Optimization for CNC Milling Machines,” MED-Vol. 4: Proceedings of Symposium on Manufacturing Science and Engineering, pp. 129-138, ASME International Mechanical Engineering Congress and Exposition, Atlanta, November 1996.
Shorr, M. J. and Liang, S. Y., “Analysis of Chatter Vibration in Multi-Flute End Milling,” DE-Vol. 93: Proceedings of Symposium on Active Control of Vibration and Noise, pp. 117-126, ASME International Mechanical Engineering Congress and Exposition, Atlanta, November 1996.
Hekman, K. A. and Liang, S. Y., “In-Process Monitoring of End Milling Cutter Runout,” International Journal of Mechatronics, Vol. 7, No. 1, pp. 1-10, 1997.
Zheng, L. and Liang, S. Y., “Identification of Cutter Axis Tilt in End Milling,” Transactions of the ASME, Journal of Engineering for Industry, Vol. 119, pp.178-185, 1997.
Shiroishi, Y., Li, Y., Liang, S. Y., Kurfess, T. R., and Danyluk, S., “Bearing Condition Diagnostics via Multiple Sensors,” Mechanical Systems and Signal Processing, Academic Press, London, 11(5), pp. 693-705, 1997.
Shiroishi, J., Li, Y., Liang, S. Y., Danyluk, S., and Kurfess, T. R., “Vibration Signal Analysis for Bearing Race Damage Diagnostics,” Keynote paper in Proceedings of 7th International Conference on Dynamic Problems in Mechanics, pp. 187-190, Angra Dos Reis, Brazil, March 1997.
Li, Y., Shiroishi, J., Danyluk, S., Kurfess, T. R., and Liang, S. Y., “Bearing Fault Detection via High Frequency Resonance Technique with Adaptive Line Enhancer,” Proceedings of 12th Biennial Conference on Reliability Stress Analysis and Failure Prevention, pp.763-772, Society for Machinery Failure Prevention Technology, Virginia Beach, April 1997.
Li. Y., Shiroishi, J., Danyluk, S., Kurfess, T., and Liang, S. Y., “Diagnostics of Roller Bearing Defects Based on Vibration and Acoustic Emission,” Proceedings of the 10th International Congress and Exhibition on Condition Monitoring and Diagnostic Engineering Management, pp. 256-267, Espoo, Finland, June 1997.
Lazoglu, I. and Liang, S. Y., “Analytical Modeling of Force System in CNC Ball-End Milling Process,” Proceedings of Biannual Mechanical Engineering Conference, MAMKON’97, pp. 416-423, Istanbul, Turkey, June 1997.
Liang, S. Y., “Control of Milling Cutter Runout by Chip Load Servo,” Proceedings of The 2nd International Conference on Industrial Tooling, pp. 141-148, Southampton, UK, September 1997.
Liang, S. Y. and Zheng, L., “System Compliance and Part Form Error in End Milling,” Proceedings of International Conference on Precision Engineering, pp. 275-280, Taiwan, November 1997.
Billington, S. A., Li, Y., Kurfess, T. R., Liang, S. Y., and Danyluk, S., "Roller Bearing Defect Detection with Multiple Sensors," ASME-IMECE, TRIB-Vol. 7, pp. 31-36, Dallas, November 1997.
Lazoglu, I. and Liang, S. Y., “An Improved Analytical Model of Force System in Ball-End Milling“ Proceedings of Symposium on Predictable Modeling in Metal Cutting as Means of Bridging Gap Between Theory and Practice: Cutting Process Modeling, pp. 135-142, ASME-IMECE, Dallas, November 1997.
Lazoglu, I. and Liang, S, Y., “Analytical Modeling of Ball-end Milling Forces,” Journal of Machining Science and Technology, Vol. 1, No. 2, pp. 219-234, 1997.
Zheng, L., Li, Y., and Liang, S. Y., “A Generalised Model of Milling Forces Cutting” International Journal of Advanced Manufacturing Technology, Vol. 14, No. 3, pp. 160-171, 1997.
Chiou, Y. S. and Liang, S. Y., “Chatter Stability of a Slender Cutting Tool in Turning with Tool Wear Effect,” International Journal of Machine Tools and Manufacture, 1997. Vol. 38, No. 4, pp. 315-327, 1998.
Liang, S. Y. and Zheng, L., “Analysis of End Milling Surface Error Considering Tool Compliance,” Transactions of the ASME, Journal of Engineering for Industry, Vol. 120, pp. 207-210, 1998.
Liang, S. Y., “Closed-Form Analytical Modeling of Milling Forces and its Applications,” Proceedings of the CIRP International Workshop on Modeling of Machining Operations, Atlanta, May 1998, pp. 131-140.
Zheng, L., Liang, S. Y., and Melkote, S. N., “Angle Domain Analytical Model for End Milling Forces,” Transactions of the ASME, Journal of Engineering for Industry, Vol. 120, pp. 252-258, 1998.
Hekman, K. A. and Liang, S. Y. “Flatness Control in Grinding by Depth of Cut Manipulation,” International Journal of Mechatronics, 8, pp. 323-335, 1998.
Liang S. Y. and Zhang, L., “End Milling Surface Error Modeling with System Compliance,” Journal of Machining Science and Technology, Vol. 2, No. 1, pp.41-56, 1998.
Shiroishi, J., Li, Y., Liang, S. Y., Danyluk, S. and Kurfess, T., "Vibration Analysis for Bearing Outer Race Condition Diagnostics", Journal of the Brazilian Society of Mechanical Sciences, Vol.21, Nº3, pp. 484-492, 1999.
Hekman, K. A. and Liang, S. Y., “Compliance Feedback Control for Part Parallelism in Grinding,” International Journal of Advanced Manufacturing Technology, Vol. 15, pp. 64-69, 1999.
Lee, K-Y, Hwang, J., Cheng, E-S, and Liang, S. Y., “A Study on the Cutter Runout Compensation by PI Control in End Mill Process,” (in Korean) Journal of the Korean Society of Precision Engineering, Vol. 15, No. 5, pp. 65-71, May 1998.
Li, Y., Billington, S. A., Kurfess, T. R., Danyluk, S., and Liang, S. Y. “Dynamic Prognostics of Rolling Bearing Condition,” Proceedings of 23rd Meeting of the Society for Machinery Failure Prevention Technology, pp. 429-430, Virginia Beach, March 30-April 3, 1998.
Billington, S. A., Li, Y., Kurfess, T. R., Liang, S. Y., and Danyluk, S., "Operating Condition Effects on Rolling Element Bearing," Proceedings of 23rd Meeting of the Society for Machinery Failure Prevention Technology, pp. 313-322, Virginia Beach, March 30-April 3, 1998.
Hwang, J, Chung, E. S., and Liang, S. Y., “Surface Quality Improvement through Cutter Runout Elimination in End Milling Process,” Proceedings of Japan-USA Symposium on Flexible Automation, pp. 1173-1178, Japan, June 1998.
Zheng, L., Liang, S. Y., and Melkote, S. N., "Angle Domain Analytical Model for End Milling Forces," Proceedings of the 3rd S. M. Wu Symposium on Manufacturing Science, pp. 50-55, Wuhan, China, June 10-12, 1998.
Li, B., Melkote, S. N., and Liang, S. Y., “A Contact Mechanics Model for Analysis of Machining Fixtures,” Proceedings of the 3rd S. M. Wu Symposium on Manufacturing Science, pp. 162-168, Wuhan, China, June 10-12, 1998.
Hekman, K. A. and Liang, S. Y., “Force Modeling for Cup Wheel Surface Grinding,” Proceedings of the ASME Manufacturing Science and Engineering Division, pp. 627-635, IMECE, Anaheim, CA, November 16-20, 1998.
Hekman, K. A. and Liang, S. Y., “Feedrate Optimization and Depth of Cut Control for Productivity and Part Parallelism in Grinding,” International Journal of Mechatronics, Vol. 9, pp. 447-462, 1999.
Li, Y., Billington, C., Zhang, C., Kurfess, T., Danyluk, S., and Liang, S. Y., “Adaptive Prognostics for Rolling Element Bearing Condition,” Mechanical Systems and Signal Processing, Academic Press, London, 13(1), pp. 103-113, 1999.
Chiou, Y. S. and Liang, S. Y., “Chatter Frequency in Turning Considering Tool Compliance and Wearland” Transactions of the ASME, Journal of Manufacturing Science and Engineering, Vol. 121, pp. 307-311, 1999.
Li, Y., Billington, C., Zhang, C., Kurfess, T., Danyluk S., and Liang, S. Y., “Dynamic Prediction of Defect Propagation on Rolling Element Bearing,” Tribology Transactions of Society of Tribologists & Lubrication Engineers (STLE), Vol. 42, No. 2, pp. 385-392, 1999.
Bell, D., Chou, J., and Liang, S. Y., “Modeling of Cutting Fluid Effect on Shop Floor Environment,” Tribology Transactions of STLE, Vol. 42, No. 1, pp. 168-173, 1999.
Li, Y. and Liang, S. Y., “Cutting Force Analysis in Transient State Milling Processes,” International Journal of Advanced Manufacturing Technology, Vol. 15, pp. 785-790, 1999.
Yang, Y., Kurfess, T. R., Liang, S. Y., and Danyluk, S., “Application of A Specialized Capacitance Probe in Bearing Diagnosis”, Wear, 225-229, pp. 1215-1221, 1999.
Li, Y., and Liang, S. Y., “Modeling of Milling Forces in Transient State” Proceedings of 6th Pam American Congress of Applied Mechanics, Vol. 7, pp. 793-796, Rio de Janeiro, Brazil, January 4-8, 1999.
Noh, J. H., Hwang, J., Liang, S. Y., and Chung, E. S., "Cutter Runout Elimination in End Milling through Two-Axes PI Force Control,” (in Korean) Journal of the Korean Society of Precision Engineering, Vol. 16, No. 6, pp. 83-89, June 1999.
Li, Y., Kurfess, T. R., Danyluk, S., and Liang, S. Y., “Bearing Prognostics Based on Adaptation of Stochastic Defect Growth Model,” Proceedings of 53th Meeting of the Society for Machinery Failure Prevention Technology, pp. 337-347, Virginia Beach, Virginia, April 19-22, 1999.
Zhang, C., Li, Y., Kurfess, T., Danyluk, S., and Liang, S., “Bearing Diagnostics Negating Operation Condition Effects,” International Journal of Condition Monitoring & Diagnostic Engineering Management, Vol. 2, No. 1, pp. 23-29, 1999.
Bell, D. D., Chou, J., Nowag, L., and Liang, S. Y., "Predictive Model for the Loss of Cutting Fluid into Machining Shop Environment," Proceedings of 32nd International Symposium on Automotive Technology & Automation (ISATA), Vienna, June 14-18, pp. 391-398, 1999.
Medaska, M. K., Nowag, L., and Liang, S. Y., "Simultaneous Measurement of The Thermal and Mechanical Effectiveness of Cutting Fluid," Proceedings of 32nd ISATA, Vienna, June 14-18, pp. 425-432, 1999.
Zhang, C., Qiu, J., Danyluk, S., Kurfess, T. R., and Liang, S. Y., "Dynamic Modeling of Vibration Signals for Bearing Condition Monitoring", 2nd International Workshop on Structural Health Monitoring, September 8-9, pp. 927-935, 1999.
Chiou, R. Y., Kwon, Y. K., and Liang, S. Y., "The RMS Characteristics of Acceleration and Force Signals Depending on Tool Wear in Stable Cutting," Proceedings on Symposium on Sensors and Controls for Manufacturing, ASME-IMECE, Med-Vol. 10, pp. 621-627, 1999.
Medaska, M. K., Nowag L, and Liang, S. Y., "Simultaneous Measurement of the Thermal and Mechanical Effectiveness of Cutting Fluid", Journal of Machining Science and Technology, Vol. 3, Issue 2, pp. 221-237, 1999.
Chen, Z., Wong, K., Li, W., Stephenson, D. A., and Liang, S. Y., "Cutting Fluid Aerosol Generation due to Spin-off in Turning Operation: Analysis for Environmentally Conscious Machining", Proceedings of Symposium on Machining Science, ASME-IMECE, MED-Vol. 10, pp. 285-291, 1999.
Lazoglu, I. and Liang, S., “Analysis of Ball-end Milling Forces with Spindle Axis Tilt,” ASME Transactions, Journal of Manufacturing Science and Engineering, Vol. 12, pp. 3-11, February 2000.
Li, B., Melkote, S., and Liang, S. Y., "Analysis of Reactions and Minimum Clamping Force of Machining Fixtures with large Contact Areas”, International Journal of Advanced Manufacturing Technology, 16, pp.79-84, 2000.
Li, Y., Kurfess, T. R., and Liang, S. Y., "Stochastic Prognostics for Rolling Element Bearings," Mechanical Systems and Signal Processing, Academic Press, London, Vol. 14, No. 5, pp. 747-762, 2000.
Chiou, Y. S. R. and Liang, S. Y., “Dynamic Modeling of Cutting Acoustic Emission via Piezo-Electric Actuator Wave Control,” International Journal of Machine Tools and Manufacture, 40 (7), pp. 927-941, 2000.
Chiou, Y. S. R. and Liang, S. Y., “Analysis of Acoustic Emission in Chatter Vibration with Tool Wear Effect in Turing” International Journal of Machine Tools and Manufacture, 40 (5), pp. 641-659, 2000.
Li, Y., Kurfess, T. R., Danyluk, S., and Liang, S. Y., “Diagnostics and Prognostics of a Single Surface Defect on Roller Bearings” International Journal of Mechanical Engineering Sciences, Part 3, Vol. 214, pp. 1173-1185, 2000.
Li, Y., Liang, S. Y., Petrof, R. C., and Seth, B. B., "Force Modeling for Cylindrical Plunge Cutting," International Journal of Advanced Manufacturing Technology, Vol. 16, pp. 863-870, 2000.
Zhang, C., Qiu, J., Kurfess, T. R., Danyluk, S., and Liang, S. Y., "Impact Dynamics Modeling of Bearing Vibration for Defect Size Estimation" International Journal of Condition Monitoring & Diagnostic Engineering Management, 3(3), pp. 37-42, 2000.
Chen, Z., Atmadi, A., Stephenson, D. A., and Liang, S. Y., “Cutting Fluid Aerosol Generation in Turning Operation” Transactions of the North American Manufacturing Research Institution, Society of Manufacturing Engineers, pp. 155-160, 2000.
Chen, Z., Atmadi, A., Stephenson, D. A., and Liang, S. Y., “Analysis of Cutting Fluid Aerosol Generation for Environmentally Responsible Machining”, Annals of International Institution for Production Engineering Research (CIRP), Volume 49/1, pp. 53-56, 2000.
Chen, Z., Atmadi, A., Stephenson, D. A., and Liang, S. Y., “Modeling and Experimental Verification of Cutting Fluid Aerosol Generation”, Proceedings of Japan-USA Symposium on Flexible Automation, pp. 425-432, 2000.
Qiu, J., Zhang, J., and Liang, S. Y., “Prognostic of Mechanical Systems Based on Damage Mechanics” Proceedings of Japan-USA Symposium on Flexible Automation, pp. 249-254, 2000.
Hekman, K. and Liang, S. Y., “Improving Part Parallelism and Productivity in Cup Wheel Surface Grinding,” CD Proceedings of Mechatronics Forum, Atlanta, September 2000.
Hecker, R. L. and Liang, S. Y., “Power Feedback Control in Cylindrical Grinding Process,” Proceedings of Symposium on Controls for Manufacturing, ASME-IMECE, Orlando, 2000, DSC-Vol. 69-2, pp. 713-718.
Chen, Z., Wong, K., Li, W., Stephenson, D. A., and Liang, S. Y., "Cutting Fluid Aerosol Generation due to Spin-off in Turning Operation: Analysis for Environmentally Conscious Machining", ASME Transactions, Journal of Manufacturing Science and Engineering, Vol. 123, pp. 506-512, August 2001.
Atmadi, A., Stephenson, D. A., and Liang, S. Y., “Cutting Fluid Aerosol from Splash in Turning: Analysis for Environmentally Conscious Machining,” International Journal of Advanced Manufacturing Technology, Vol. 17, pp. 238-243, 2001.
Zhang, C., Qiu, J., and Liang, S.Y., “Bearing Failure Prognostic Model Based on Damage Mechanics and Vibration Monitoring”, Tribology Transactions of STLE, Vol. 44, Number 4, October 2001, pp. 603-608.
Hekman, K., Hecker, R., and Liang, S. Y., “Adaptive Power Control of Cylindrical Traverse Grinding” Proceedings of 3rd International Conference on Metal Cutting and High Speed Machining, Metz, France, June 2001. Volume II, pp. 262-264.
Liang, S. Y. and Hecker, R. L., “Machining Process Monitoring and Control: The State of the Art,” Proceedings of 12th National Conference on Automation Technology, Taiwan, pp. 47-48, May 24-26, 2001.
Qiu, J., Zhang, C., Seth, B. B., and Liang, S. Y., “Damage Mechanics Approach for Bearing Lifetime Prognostics” Mechanical Systems and Signal Processing, Vol. 16, Issue 4, pp. 705 - 718, 2002.
Chen, Z, Yamaguchi, H., and Liang, S. Y., “Predictive Modeling of Cutting Fluid Aerosol in Grinding Process,” Transactions of the North American Manufacturing Research Institution, Society of Manufacturing Engineers, pp. 277-285, 2002.
Zhang, C., Le, M. T., Seth, B. B., and Liang, S. Y., “Bearing Life Prognosis under Environmental Effects based on Accelerated Life Testing” Journal of Mechanical Engineering Science, Vol. 206, Part C, pp. 509-516, 2002.
Hekman, K. A., Hecker, R. L., and Liang, S. Y., “Fixed-Gain and Adaptive Controls for Constraint Power Cylindrical Traverse Grinding,” Proceedings of 6th International Conference on Production Engineering and Design for Development, Cairo, February 2002.
Huang Y. and Liang, S. Y., “Force Modeling in Shallow Cuts with Large Negative Rake Angle and Large Nose Radius Tools– Application to Hard Turning”, International Journal of Advanced Manufacturing Technology, vol. 22, pp. 626-632, 2003.
Zhang, C., Chuckpaiwong, I., Seth, B. B., and Liang, S. Y., “Mechanical Component Lifetime Estimation Based on Accelerated Life Testing with Singularity Extrapolation”, Mechanical Systems and Signal Processing, Vol. 16, Issue 5, pp. 817 - 829, 2002.
Liang, S. Y., Hecker, R. L., and R. Landers, “Machining Process Monitoring and Control: The State of the Art,” CD Proceedings Manufacturing Engineering Division Symposium, IMECE, ASME, 2002, Paper # 32640.
Hecker, R. and Liang, S. Y., “Low Feed Control in Plunge Grinding under Friction Effect,” Proceedings of Japan-USA Symposium on Flexible Automation, pp. 61-66, Vol. 1, 2002.
Zhang, C. and Liang, S. Y., “Implementation of Condition-based Maintenance of Rolling Element Bearings”, Proceedings of Japan-USA Symposium on Flexible Automation, pp. 1155-1165, Vol. 3, 2002.
Hecker, R. L. and Liang, S. Y., “Power Feedback Control in Cylindrical Plunge Grinding with an Inner Repetitive Position Control Loop,” Proceedings of the 17th IEEE International Symposium on Intelligent Control, Vancouver, Canada, pp. 642-647, 2002.
Zhang, J. Y. and Liang, Y. S., “Sensor Integrated on-line Prognostics of Bearing Incipient Defect Based on Artificial Neural Network,” Proceedings of the 57th Meeting of the Society for Machinery Failure Prevention Technology, Virginia Beach, April 14-18, pp. 43-52, 2003.
Autret R. and Liang S. Y., “Minimum Quantity Lubrication in Finish Hard Turning,” CD Proceedings of International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment, and Management, March 26-28, 2003.
Kirkland, E. and Liang, S. Y., “A Nano Coordinate Measuring Machine for Optical Dimensional Metrology”, Proceedings of International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment, and Management, CD, March 26-28, 2003.
Hecker, R. L., Ramoneda, I. M., and Liang, S. Y., “Active Grain Density Calculation and Force per Grain Estimation in Grinding,” Transactions of North American Manufacturing Research Institution, Society of Manufacturing Engineering, pp. 281-288, 2003.
Liu, K., Li, X., and Liang, S. Y. “Nanometer Scale Ductile Cutting of Tungsten Carbide,” Transactions of North American Manufacturing Research Institution, Society of Manufacturing Engineering, pp. 153-160, 2003.
Zhang, J. Y. and Liang, S. Y., “Hard Cutting Technology and Its Application to Die and Mold Making,” Proceedings of Moldmaking Conference 2003, pp. 262-276, 2003.
Hecker, R., Ramoneda, I., and Liang, S. Y., "Analysis of Wheel Topography and Grit Force for Grinding Process Modeling,” Journal of Manufacturing Processes, Society of Manufacturing Engineers, Vol. 5, No. 1, pp.13-23, 2003.
Hecker, R. L. and Liang, S. Y., “Predictive Modeling of Surface Roughness in Grinding,” International Journal of Machine Tools and Manufacture, 43, pp. 755-761, 2003.
Huang, Y., and Liang S. Y., “Modeling of Cutting Temperature Distribution under Tool Flank Wear Effect”, Journal of Mechanical Engineering Science, Vol. 217, No. C11, pp. 1195-1208, 2003.
Huang, Y. and Liang, S. Y., “CBN Tool Wear Rates Modeling in Finish Hard Turning,” CD Proceedings of Symposium on Advances on Machining of Hard Materials, Proceedings of IMECE ’03, ASME, IMECE2003-42165, November 2003.
Hecker, R. L. and Liang, S. Y., “Cylindrical Grinding Cycle Design based on Final Part Quality Constraints,” CD Proceedings of Symposium on Accuracy and Stability in Machining, Proceedings of IMECE ’03, ASME, IMECE2003-42166, November 2003.
Zhang, C. and Liang, S. Y., “Condition-based Maintenance of Rolling Element Bearings”, International Journal of COMADEM, Vol. 7, No. 4, pp. 3-12, October 2004.
Huang, Y. and Liang, S. Y., “Cutting Forces Modeling Considering the Effect of Tool Thermal Property – Application to CBN Hard Turning”, International Journal of Machine Tool and Manufacture, Vol. 43, pp. 307-315, 2003.
Kirkland, E. Kurfess, T. R., and Liang, S. Y., “A Optical Coordinate Measuring Machine for Nanoscale Dimensional Metrology,” Journal of Advanced Computational Intelligence and Intelligent Informatics, Vol. 8 No. 1., pp. 39 - 44, January 2004
Huang, Y. and Liang, S. Y., “Modeling of CBN Tool Crater Wear in Finish Hard Turning” International Journal of Advanced Manufacturing Technology, Vol. 24, pp. 632-639, 2004.
Chiou, R. Y., Kwon Y. K., and Liang S. Y., “Modeling the Effect of Flank Wear on Machining Thrust Stability,” International Journal of Advanced Manufacturing Technology, Vol. 23, pp. 857-864, 2004.
Huang, Y. and Liang, S. Y., “Modeling of CBN Tool Flank Wear Progression in Finish Hard Turning”, ASME Transactions, Journal of Manufacturing Science and Engineering, Vol. 126, No. 1, pp. 98-106, February 2004. (ASME Blackall Machine Tool and Gage Award, Winter, 2005)
Liang, S. Y., Hecker, R. L., and Landers, R. G., “Machining Process Monitoring and Control: The State-of-the-Art,” ASME Transactions, Journal of Manufacturing Science and Engineering, Vol. 126, pp. 297-310, May 2004.
Liu, K., Li, X., Liang, S. Y., Liu X. D., “Nanometer Scale Ductile Mode Cutting of Soda-Lime Glass,” Transactions of North American Manufacturing Institution of the Society of Manufacturing Engineers, Vol. 32, pp. 39-45, 2004.
Huang, Y. and Liang, S. Y., “Effect of Cutting Conditions on Tool Performance in CBN Hard Turning,” Transactions of North American Manufacturing Institution of the Society of Manufacturing Engineers, Vol. 32, pp. 511-518, 2004.
Zhang, J. Y. and Liang, S. Y., “Handling Constraints for Manufacturing Process Optimization Using Genetic Algorithm” Proceedings of International Conference on Precision Engineering (ICoPE), Singapore, pp. 76-83, March 2004.
Kirkland, E., Kurfess, T. R., and Liang, S. Y.,“A Nano Coordinate Measuring Machine using Auto-Focusing Probe,” Proceedings of International Conference on Precision Engineering (ICoPE), Singapore, pp. 70-75, March 2004.
Zhang, J. Y., and Liang, S. Y., “A Mixed Integer Evolutionary Algorithm for Manufacturing Process Optimization, Part I: Methodology Formulation,” Proceedings of Japan-USA Symposium on Flexible Automation, CD, Denver, Colorado, July 18-21, 2004,
Zhang, J. Y., and Liang, S. Y., “A Mixed Integer Evolutionary Algorithm for Manufacturing Process Optimization, Part II: Application to Hard Turning Process Optimization,” Proceedings of Japan-USA Symposium on Flexible Automation, CD, July 18-21, 2004, Denver, Colorado.
Hwang, J., Chung, Eui-Sik, and Liang, S. Y., “Behavior Analysis of the Cutting Fluid Aerosols for Environmentally Conscious Machining,” Proceedings of Japan-USA Symposium on Flexible Automation, CD, July 18-21, 2004, Denver, Colorado.
Kirkland, E., Kurfess, T. R., and Liang, S. Y.,“A Six-DOF Nano CMM based on Auto-Focusing Probe,” International Journal for Manufacturing Science and Technology, Vol. 6, No. 1, pp. 11-15, 2004.
Liang, S. Y., “Machining and Metrology at Micro/Nano Scale,” Proceedings of the 1st International Conference on Positioning Technology, Hamamatsu, Japan, pp. 23-28, June 9-11, 2004.
Hecker, R. and Liang, S. Y., “Open Architecture System for Power Control in Cylindrical Grinding”, Proceedings of Argentinian Congress of Automatic Control Argentinean Conference, International Federation of Automatic Control (IFAC), Buenos Aires, August 31 – September 3, 2004.
Park, H. W., Liang, S. Y, Liu, W. L., and Hsieh, S.-B. “On the Performance Advantages of Microscale Machine Tools,” Proceedings of 4th International Workshop on Microfactories (IWMF2004), pp. 92-97, October 15-17, 2004, Shanghai, China.
Li, X. and Liang, S. Y., “Nanometer Scale Ductile Cutting of Tungsten Carbide,” Journal of Manufacturing Processes, Society of Manufacturing Engineers, Vol. 6, No. 2, pp. 187-195, 2004.
Su, J.-C, Liang, S. Y., Wang Lin Liu, and Tzu Chi Jan, “Ceramic Micro/nanoparticle Size Evolution in Wet Grinding in Stirred Ball Mill” Transactions of ASME, Journal of Manufacturing Science and Engineering, Special Edition on Micro/Meso-scale Mechanical Manufacturing, Vol. 126, pp. 779-786, November 2004.
Cox, D., Newby, G., Park, H. W., and Liang, S. Y., “Design and Performance Evaluation of a Microscale Machining Center for Precision Manufacturing“, CD Proceedings of ASME-IMECE, 2004.
Huang, Yong and Liang, S. Y., “Effect of Cutting Conditions on Tool Performance in CBN Hard Turning,” Journal of Manufacturing Processes, Vol. 7, No. 1, 2005.
Huang, Y. and Liang, S. Y., “Modeling of Cutting Forces under Hard Turning Cutting Condition Considering Tool Wear Effect,” ASME Transactions, Journal of Manufacturing Science and Engineering. Vol. 127, No. 2, pp. 262-276, May 2005
Zhang, X., Xu, R., Kwan, C., Liang, S. Y., Xie, Q., and Haynes, L., “An Integrated Approach to Bearing Fault Diagnostics and Prognostics,” Proceedings of the American Control Conference, pp. 2750 - 2755, Portland, OR, June 2005
McFarland, A. W., Colton, J. S., Cox, D., and Liang, S. Y., “Manufacturing of Microcantilever Sensors” CD Proceedings of IMECE ASME-IMECE, Orlando, FL, November 5-11, 2005
Li, K. M. and Liang, S. Y., “Predictive Models for Flank Wear in Near Dry Machining” CD Proceedings of IMECE ASME-IMECE, November 5-11, 2005, Orlando, FL.
Cox, D., McFarland, A. W., Liang, S. Y., and Colton, J. S., “Machining and Molding of Microcantilever Sensors,” Proceedings of the 3rd International Conference on Leading Edge Manufacturing in the 21st Century (LEM 21), Nagoya, Japan, pp. 865-869, October 19-22, 2005.
Zhang, J., Liang, S. Y., Yao, J., Chen, J. M., and Huang, J. L., “Evolutionary Optimization of Machining Processes,” Journal of Intelligent Manufacturing, Vol. 17, No. 2, pp. 203-216, April 2006.
Cox, D., Newby G., Park, H. W., Liang, S. Y., Liu, W. L., Hsieh, S. B., and Hwang, J., “The Development of a Micro-Scale Machining Center,” CD Proceedings of 2nd Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment and Management (HNICEM) International Conference, 2005.
Rodolfo, H., Liang, S. Y., Alique, J. R., Alique, A., Ros, S. "Fuzzy Control of Spindle Torque in High-Speed Milling Processes,” CD Proceedings of IMECE ASME-IMECE, November 5-11, 2005, Orlando, FL.
Liu, K., Li, X. P., and Liang, S. Y., “The Mechanism of Ductile Chip Formation in Cutting of Brittle Materials,” International Journal of Advanced Manufacturing Technology, Vol. 10, pp. 1 – 10, 2006
Liu, K., Li, X., Liang, S. Y., Liu X. D., “Nanometer Scale Ductile Mode Cutting of Soda-Lime Glass,” Journal of Manufacturing Processes, Vol. 7, No. 2, pp. 95-101, 2005.
Huang, Y. and Liang, S. Y., “Cutting Temperature Modeling Based on Non-uniform Heat Intensity and Partition Ratio,” Machining Science and Technology. Vol. 9, Issue 3, pp. 301-323, 2005.
Zhang, J. Y. and Liang, S. Y., “On Surface Roughness in Finish Turning of Hardened Steels,” Transactions of North American Manufacturing Engineering Research Institution of the Society of Manufacturing Engineers, Vol. 34, pp. 515-522, 2006.
Li, K. M. and Liang, S. Y., “Cutting Fluid Aerosol Generation in Near Dry Turning,” International Journal of Manufacturing Research, Vol. 1, No. 3, pp. 183-299, 2006
Cox, D., Newby G., Park, H. W., Liang, S. Y., Liu, W. L., Hsieh, S. B., and Hwang, J., “Precision Machining with Micro-Scale Vertical Machining Center,” Journal of Advanced Computational Intelligence and Intelligent Informatics, Vol. 10, No. 2, pp. 187-195, March 2006.
Liang, S. Y., Hecker, R., “New Applications and Trends in Machining Process Monitoring and Control,” CD Proceedings of Forum de la Automática, Barcelona, March 30, 2006
Liang, S. Y., “On Current Advanced Research Projects in the Area of Hard Turning,” reviewed and published by Association for Manufacturing Technology (AMT), Technology Assessment, June 2006.
Liang, S. Y., “Machining and Metrology at Micro and Nano Scale,” Proceedings of International Symposium on Precision Mechanical Measurements (ISPMM), Urumqi, Xinjiang, China, August 2-6, 2006, pp. 2-10.
Li, Kuan-Ming and Liang, S. Y., “Modeling of Cutting Temperature in Near Dry Machining,” ASME Transactions, Journal of Manufacturing Science and Engineering, Vol. 128, Issue 2, pp. 416-424, 2006.
Park, H. W. and Liang, S. Y., “Optimal Dimensioning of Miniaturized Machine Tools,” CD Proceedings of ASME International Manufacturing Science and Engineering Conference (MSEC), October 2006
Liang, S. Y., “Micro and Nano Scale Mechanical Machining,“ CD Proceeedings of 7th Asia Pacific Conference on Materials Processing (APCMP), Singapore, December 4-6, 2006.
Newby, G., Venkatachalam, S., and Liang, S. Y., “Empirical Analysis of Cutting Force Constants in Micro End Milling Operations,” CD Proceeedings of 7th Asia Pacific Conference on Materials Processing (APCMP), Singapore, December 2006
Xie, Qiulin, Liang, S. Y., “Modeling of Linear Motor Feed Drives for Grinding Machines,” International Journal of Manufacturing Research, Vol. 1, No. 1, pp. 41-58, 2006.
Zhang, J. Y. and Liang, S. Y., “Process Optimization of Finish Turning of Hardened Steels,” Materials and Manufacturing Processes, Vol. 22, pp. 107-113, 2007.
Zhang, J. Y., Morehouse, J. B., Liang, S. Y., Jun Yao, and Xiaoqin Zhou, “Handling Constraints for Manufacturing Process Optimization Using Genetic Algorithms,” International Journal of Computer Applications in Technology (IJCAT), Vol. 28, No. 1, pp. 9-19, 2007.
Park, H. W. and Liang, S. Y., “Microgrinding Force Modeling based on Microscale Single Grain Interaction Analysis,” International Journal of Manufacturing Technology and Management, Special Issue on High Performance Grinding Processes, Vol. 12, No. 1/2/3, pp. 25-38, 2007.
Huang, Y., Chou, Y. K., and Liang, S. Y., "CBN Tool Wear in Hard Turning: A Survey on Research Progresses," International Journal of Advanced Manufacturing Technology, Vol. 35(5-6), pp. 443-453, 2007.
Hecker, R. L. and Liang, S. Y., “Grinding Force and Power Modeling based on Chip Thickness Analysis” International Journal of Advanced Manufacturing Technology, Vol. 33, No. 5-6, pp. 449-459, 2007.
Li, Kuan-Ming and Liang, S. Y., “Predictive Modeling of Flank Wear in Turning under Flood Cooling,” ASME Transactions, Journal of Manufacturing Science and Engineering, June 2007, Vol. 129, pp. 513-519.
Zhang, J. Y., Liang, S. Y., Zhang, G., Yen, D., “Intelligent Modeling of Residual Stress Profile in Finish Hard Turning,” Materials and Manufacturing Processes, Vol. 21, No. 1-2, pp. 39-45, 2006.
Li, K. M. and Liang, S. Y., “Modeling of Cutting Forces in Near Dry Machining under Tool Wear Effect,” International Journal of Machine Tools and Manufacturer, Vol. 47, Issues 7-8, pp. 1292-1301, 2007
Li, K. M. and Liang, S. Y., “Performance Profiling of Minimum Quantity Lubrication in Machining,” International Journal of Advanced Manufacturing Technology, Vol. 35, No. 3-4, pp. 226-233, 2007
Venkatachalam, S., Liang, Y. S., “Effects of Plowing Forces and Friction Coefficient in Micro-scale Machining,” ASME Transactions, Journal of Manufacturing Science and Engineering, Vo. 129, No. 2, pp. 274-280, April 2007.
Newby, G., Venkatachalam, S., and Liang, S. Y., “Empirical Analysis of Cutting Force Constants in Micro End Milling Operations,” Journal of Materials Processing Technology, 192-193, 2007. pp. 41-47.
Liang, S. Y., and Su, J.-C., “Residual Stress Modeling in Orthogonal Machining,” Annals of International Institution for Production Engineering Research (CIRP), Vol. 56/1, 2007, pp. 65-68
Su, J.-C. and Liang, S. Y., “Predictive Modeling of Machining Residual Stresses Considering Tool Edge Effects,” submitted to International Journal of Machine Tools and Manufacture. (under review)
Zhang J. Y., Liang, S. Y., and Yen, D., “Optimization of the Finish Hard Turning Process for Hardened 52100 Steel with PCBN Tools,” submitted to International Journal of Manufacturing Research, Vol. 2, No. 4, pp. 428-447, 2007.
Murtagoam. G. R., Hecker, R. L., Liang, S. Y., and Danyluk, S., “Plastic Deformation Depth Modeling on Grinding of Gamma Titanium Aluminides,” submitted to ASME Journal of Manufacturing Science and Technology, (under review)
Haber, R. E., Schmittdiel, M. C., and Liang, S. Y., “Remote Fuzzy Control of Spindle Torque in High-performance Milling Processes,“ submitted to IEEE Transactions on Control Systems Technology, (under review)
Liang, S. Y. and Abraham, B., “Predictive Modeling and Optimization of High Performance Machining,” CD Proceedings of 9th Conference on Machining and Advanced Manufacturing Technology, Harbin, China, August, 2007
Liang, S. Y. and Abraham, B. “Predictive Modeling and Strategic Optimization of High-Performance Machining,” CD Proceedings of International Conference on Advanced Manufacturing (ICAM), Tainan, Taiwan, November 26-28, 2007.
Park, H. W. and Liang S. Y., “Analysis of the Scale Effect for Microscale Machine Tools,” CD Proceedings of ASME International Manufacturing Science and Engineering Conference (MSEC), October 15-18, 2007, Atlanta. MSEC2007-31034.
Chao, R.-M., Li, S.-Y., Hsu C.-C., and Liang, S. Y., “Characteristic Evaluation of Silicon-based MEMS Acoustic/Acceleration Sensor”, CD Proceedings of MSEC, October 15-18, 2007, Atlanta. MSEC2007-31131.
Hanna, C. R., Chao, R.-M., and Liang, S. Y., “Specification of Shear Zone Characteristics in Achieving Desired Residual Stress Profile”, CD Proceedings of MSEC, October 15-18, 2007, Atlanta. MSEC2007-31171.
Wang, J. J., Hou, J. L., Hsu, F. C., and Liang, S. Y., “A RSS Method for Estimating Hole Dimension Error in a Batch Micro-EDM Process,” CD Proceedings of ASME International Manufacturing Science and Engineering Conference (MSEC), October 15-18, 2007, Atlanta. MSEC2007-31063.
Li, Kuan-Ming and Liang S. Y., “Modeling of Flank Wear In Near Dry Turning Under Built-Up Edge Effect,” CD Proceedings of International Forum on Systems and Mechatronics (IFSM), Tainan, Taiwan, December 3-6, pp.147-156, 2007.
Xie Q. and Liang, S. Y., “Linear Motor Feed Drives for Grinding Machine: Modeling and Control Strategies,” CD Proceedings of 9th Cairo University International Conference on Mechanical Design and Production (MDP-9), Egypt, 2008.
Cardi,, A. A., Bement, M. T., and Liang, S. Y., “Workpiece Dynamic Analysis and Prediction during Chatter of Turning Process,” accepted by Mechanical Systems and Signal Processing, (in print)
Damianakis, M. A., Bement, M. T., and Liang, S. Y., “Kinematics Prediction and Experimental Validation of Machined Surface Roughness.” submitted to International Journal of Advanced Manufacturing Technology. (under review)
Venkatachalam, S., Li, X., and Liang S. Y., “Modeling the Effects of Crystallography on Micro-scale Machining of Polycrystalline Brittle Materials” submitted to ASME Journal of Manufacturing Science and Engineering. (under review)
Hanna, R. Hanna, Liang, S. Y., and Chao, Ru-Min, “Achieving Machining Residual Stresses Through Model-Driven Planning of Process Parameters,” submitted to Transactions of North American Manufacturing Research Institution 2008, (under review)
Cardi, A. A., Bement, M. T., and Liang, S. Y., “Workpiece Dynamics During Stable Cutting in a Turning Operation,” submitted to International Journal of Manufacturing Research, (under review)
Su, J.-C., Young, K. A., Ma, K., Srivasta, S., Morehouse, J. B., and Liang, S. Y., “Modeling of Residual Stress in Milling,” submitted to International Journal of Machine Tools and Manufacture, (under review)
Venkatachalam, S., Li, X., and Liang, S. Y., “Predictive Modeling of Transition Undeformed Chip Thickness in Ductile Regime Micro-Machining of Single Crystal Brittle Materials,” submitted to Journal of Materials Processing Technology, (under review)
Venkatachalam, S., Cai, M., Li, X., and Liang, S. Y., “Crystallographic Effects on Ultraprecision Machining of Polycrystalline Brittle Materials,” submitted to Materials and Manufacturing Processes, (under review)
Park, H. W. and Liang, S. Y., “Force Modeling of Micro-scale Grinding Process incorporating Thermal Effects,” submitted to International Journal of Advanced Manufacturing Technology, (under review).
Li, K-M and Liang, S. Y., “Tool Flank Wear Modeling in Near Dry Turning under Built-Up Edge Effect,” submitted to International Journal of Manufacturing Technology and Management. (under review).
Park, H. W. and Liang, S. Y., “Force Modeling of Micro-Grinding incorporating Crystallographic Effects,” submitted to International Journal of Machine Tools and Manufacture. (under review)
Park, H. W., Liang, S. Y., and Youn, J. W., “Characterizing the Topography of a Micro-Grinding Wheel,” submitted to International Journal of Manufacturing Research. (under review)
Xie, Q. and Liang, S. Y., “Robust Servo Control with Disturbance Observer based Sliding Mode Control for Linear Motor Feed Drives,” submitted to Proceedings of International Symposium on Flexible Automation 2008. (under review)
Other Publications (Non-refereed)
Liang, S. Y., "Dynamic Dielectric Monitoring of In-Situ Consolidation of Thermoplastic Filament Winding," Proceedings of the NSF Design and Manufacturing Systems Grantees Conference, pp. 1063-1067, Atlanta, January 1992.
Liang, S. Y., and Urquhart-Foster, J. A., "Filament Winding Process Monitoring via Dynamic Dielectric Analysis," Proceedings of the NSF Design and Manufacturing Systems Grantees Conference, pp. 217-222, Charlotte, January 1993.
Liang, S. Y. and Wang, J. J., "Convolution Analysis of Dynamic Forces in Milling," Proceedings of the NSF Joint-Taiwan Symposium on Advanced Manufacturing Processes, pp. 51-65, Atlanta, February 1993.
Chiou, Y. S., Chung, E. S., and Liang Y. S., “Neural-network Based Detection of Tool Wear and Chatter in Machining,” Proceedings of the 17th Annual Conference of CCAAPA, pp. 26-36, Atlanta, July 1993.
Liang, S. Y., and Urquhart-Foster, J. A., "A Dynamic Dielectric Sensor for Process Monitoring of Filament Winding,” Proceedings of the NSF Design and Manufacturing Systems Grantees Conference, pp. 603-604, Boston, January 1994.
Liang, S. Y., “Closed-form Analytical Modeling of Milling Forces and its Applications,” Proceedings of CIRP International Workshop on Modeling of Machining Operations, pp. 131-140, May 19, Atlanta, 1998.
Le, M. T., Zhang, C., and Liang, S. Y., “Bearing Life Testing Under Accelerated Environmental Condition,” Proceedings of National Undergraduate Research Opportunities Programme' Congress, September 2000. (by invitation only)
Autret, R. and Liang, S. Y., “Near Dry Finish Machining of Hardened Steel,” CD Proceedings of NSF Division of Design and Manufacturing Innovation Grandees Conference, January 2003.
Li, Kuan-Ming and Liang, Steven Y., “Predictive Modeling of Environmental Impact in Near Dry Turning,” CD Proceedings of NSF-Division of Design and Manufacturing Innovation Grandees Conference, January 2004.
Li, Kuan-Ming and Liang, Steven Y., “Predictive Modeling of Environmental Impact and Tool Performance in Near Dry Turning,” CD Proceedings of NSF-Division of Design and Manufacturing Innovation Grandees Conference, January 2005.
Li, Kuan-Ming and Liang, Steven Y., “Analysis of Environmental Impact and Tool Performance in Near Dry Turning,” CD Proceedings of NSF-Division of Design and Manufacturing
